Micro-Soldering and Board-Level Repair in Broken Arrow, Serving Tulsa

Component-level board repair, here in Broken Arrow

Micro-soldering repairs the board itself. A single failed capacitor, a corroded resistor or a cracked joint under a power chip is replaced, and the board is kept.

Request a Board Diagnostic
4.8 stars from 662 Google reviews Lifetime warranty on screens FREE general diagnostics Broken Arrow shop, minutes from Tulsa

HDMI Port Replacement

$125

The most common board-level job we see, on consoles and on laptops.

Flat rate, reinforced

Book HDMI Repair

Board Diagnostics

$50 to $150

Priced by time and difficulty.

3 to 7 business days

Book a Board Diagnostic

General Diagnostics

FREE

The board is inspected under the microscope and on thermal, and the price follows the diagnosis.

Start Free

Board-level repair explained

The difference between swapping a module and repairing the board under it.

Hundreds of parts, one failure

A logic board carries hundreds of components measured in fractions of a millimeter. One failed capacitor, one corroded resistor, or one cracked joint under a power chip stops the whole device.

The math on replacement

Replacing the board costs most of what the device is worth. Replacing the failed component costs a fraction of it.

Microscope, controlled heat, certification

A microscope, heat controlled tightly enough not to lift neighboring parts, and a technician trained to certified soldering standards.

Certifications on the bench

Our lead technician is Umair Zia.

Soldering

IPC J-STD-001, the industry standard for soldered electrical and electronic assemblies

Assembly

IPC-A-610, acceptability of electronic assemblies

Electronics

ETA CET, certified electronics technician

IT certifications

CompTIA A+, Network+, Security+, and Server+

Component-level work we perform

5 categories, from the routine to the deepest end of the bench.

HDMI port repair

Ports on consoles and laptops are soldered straight to the board. Replacement means desoldering, cleaning the pads, and fitting a new port without lifting a trace. Full detail on the HDMI port repair page.

$125

FPC connector replacement

The small sockets that screens, batteries, and cameras plug into. They tear off under a careless pry, and the socket has to be replaced under the microscope.

Capacitors, resistors, and diodes

Passives fail from liquid, voltage spikes, and age. Finding the failed one is the skill, and thermal imaging locates it. A shorted component heats up before it shows anywhere else.

IC replacement

Power management, charging, audio, and backlight driver ICs removed and replaced. The laser desoldering station and the 4K microscope earn their place on this work.

Liquid damage board recovery

Corrosion spreads under chips where no amount of drying reaches. Recovery means ultrasonic cleaning, then tracing what the corrosion destroyed, then replacing it. See water damage repair.

A microscope, controlled heat and a vacuum laminator are all on one bench here.

Get It Under the Scope

The bench

Board-level repair runs on equipment. The full bench is on our About page.

TBK R-2201

Infrared laser desoldering station with a 4K electron microscope.

Qianli Supercam X

3D thermal imaging camera for locating shorts and current leakage on a powered board.

M-Triangel 20W

Fiber laser for separating bonded back glass from the frame. See back glass replacement.

Vacuum OCA laminator

Screen refurbishing and relamination without trapped air or bubbles.

For businesses and repair shops

We take board-level work on a wholesale basis. Call (918) 883-8293 for pricing.

Repair shops

Board work at wholesale rates. We are local, and we do not compete with you for the customer relationship.

Schools and districts

Chromebook, laptop, and tablet fleets, including charge ports and FPC connectors at volume.

Businesses

Point-of-sale hardware, laptops, and equipment where a board repair beats a replacement cycle.

Diagnostics, turnaround, and warranty

Diagnostics

General diagnostics free. Board-level $50 to $150 by time and difficulty

Time on the bench

3 to 7 business days

Warranty coverage

90 days on all board-level repairs, covering parts and labor

Location

2409 W Kenosha St, Suite 137, Broken Arrow. Every board repair is done at this bench.

The diagnostic says whether the board is worth saving.

Send In the Board

Board-level micro-soldering near Tulsa

The bench is in west Broken Arrow where Highway 51 becomes Kenosha Street, about 15 to 25 minutes from most of Tulsa. Finding the failed component is most of the job, and boards stay here under the microscope for 3 to 7 business days. The repair price follows the diagnosis before you make the drive. Everyday phone and tablet work for the same customers is covered on our page for Tulsa customers.

HDMI ports off the mainboard

Console and laptop ports are soldered to the board. The fix is a desolder, a pad clean and a new port fitted without lifting a trace. More on HDMI port repair.

Flat $125

Corrosion after a spill

Liquid keeps eating traces under the chips long after the device dries. The board gets cleaned ultrasonically and then traced for what the corrosion took out. More on water damage repair.

Data off a board that will not boot

Bringing a board up long enough to pull the files is a different goal from restoring the device. More on data recovery.

Frequently asked questions

Can you explain micro-soldering?

Component-level repair on the board itself. Individual chips, connectors and passives come off and go back on under a microscope, so the failed part is replaced and the board is kept.

Do other shops send this work away?

It needs a microscope, hot air, a laser desoldering station and thermal imaging, plus the hours to learn all four. Shops without them replace parts, so a board fault turns into a quote for a new device.

How much does board-level work cost?

Board diagnostics run $50 to $150 by time and difficulty, and you get the repair price before any work starts. General diagnostics are free.

How long does a board repair take?

3 to 7 business days. Locating the fault is most of the job, and hurrying that part is how boards get damaged further.

Can you recover data from a board that will not power on?

Often yes. Bringing a board up long enough to pull the data is a different goal from restoring the device, and we will say which of the two is realistic.

Related services

HDMI Port Repair

Flat $125, soldered and reinforced here.

Learn More

Water Damage Repair

Bring it in unpowered. Corrosion cleaned here.

Learn More

Laptop & Computer Repair

Hardware, software, and board-level work.

Learn More

Bring us the board

2409 W Kenosha St, Suite 137, Broken Arrow, OK. Monday to Friday 10am to 7pm, Saturday 12pm to 6pm.

Get a Free Quote Call (918) 883-8293 Business & Wholesale Pricing
iPhone Repair Samsung & Android Laptop & Computer Game Console Repair Data Recovery Repair prices Same-day repair All Repairs
Request a repair quote from TechDaddy
SiteLock security verification for techdaddyus.com